How to Make an Ipod Work Again

March 27, 2022 Post a Comment

Download Commodity

Download Article

Nothing is more frustrating than when our most essential devices stop working. The thought of having to brand information technology through your day without music may have you down, but luckily iPods are easily repairable for all but the most egregious problems. From difficult drive problems to cracked screens, nearly whatsoever issue is repairable with patience and the right equipment. Attempt one of the methods below to become your iPod dorsum upwardly and running.

ane

Check the Hold switch. If the Hold switch is toggled on, your iPod will not accept any input. Check the Concur switch, and toggle it on and off a few times, before y'all move on to more circuitous solutions.
ii

Bank check the battery. As your iPod gets older, its battery life volition begin to shrink considerably. In that location'south a take a chance that your iPod won't function because it has tuckered its battery without yous realizing. Attempt plugging it in for near an hour and and so trying again.

Advertisement
three
Reset the iPod. If your iPod is frozen and unresponsive, the quickest and most common fix is to perform a reset. This volition reboot the iPod and kickoff the operating system over. Resetting your iPod will not cause whatsoever loss of data.
- To reset an iPod Touch, press and concord the Power and Dwelling house buttons for about x seconds until the Apple logo appears.
- To reset a classic iPod, press and hold the Carte du jour and Select buttons for about viii seconds until the Apple logo appears.
4
Restore your iPod. If resetting your iPod withal doesn't set up the issue, you tin restore your iPod to factory weather condition so reload your settings through a backup. This will fix well-nigh of the software problems with your iPod.
- Connect your iPod to your computer and open iTunes. Make sure that you have the latest version of iTunes installed.
- If your iPod does not show upward in iTunes when you plug it in to your figurer, you lot will need to put it into Recovery Mode beginning.
- Backup your iPod. Before restoring the iPod, make certain that yous back up your data and settings first. Click the "Back Up Now" push button in the iTunes Summary page to fill-in your iPod to either your computer or to iCloud.
- Click the "Restore iPod" button to begin the Restore process. The restore process can take several minutes to complete.
- Reload your old backup. Once the restoration is complete, you can either use it as if information technology was new, or restore your quondam fill-in. If yous choose to restore the backup, choose the location (iTunes or iCloud) and the engagement of the backup file.
- See this guide for more details on restoring your iPod.
Advertisement

1
Don't turn the iPod on. If your iPod barbarous in the pool or into a full sink, don't effort to turn information technology on. This could cause irreversible impairment past shorting out all of the components. Yous will need to remove the wet before trying to power it on again.
- Don't only wipe the phone dry out and try to use it. The water can cause serious harm to the within of the phone when it is wet.
two
Bury the iPod in rice. While the most effective way to remove the moisture is to put the iPod into a bag of silica gel packets, about people don't accept these handy. Instead, put your iPod into a pocketbook or bowl full of rice and brand certain information technology is completely covered. The rice volition draw the moisture out of the device over time.
- This could crusade your iPod to go a lot of dust inside, merely information technology sure beats information technology being broken for good.
- Seal the handbag or container while you let it sit.
3
Expect 24 hours before removing the iPod. It will take a while for all of the moisture to become sucked out of the iPod. You desire it to be os dry when you lot try turning it back on, and then give the rice enough of fourth dimension to blot all of the water.^[1]
- Don't use a pilus dryer to dry the iPod. The estrus from the blower could crusade more harm than good.
Advert

i
Determine if the difficult drive is the problem. If your iPod is displaying a binder icon for the mistake, then it is having difficulties accessing the difficult drive. Oftentimes, this is caused by an ill-fitting hard drive. Luckily, securing the drive is fairly straight-forward.
- All versions of the iPod Touch, iPod Shuffle, and iPod Nano use wink retentivity instead of a traditional hard drive. This means at that place are no moving parts that can neglect or connections that can get severed. There is no practical way to secure or supervene upon an iPod Impact hard drive, as the wink memory unit is built into the circuitry.
2

Toggle the Hold switch on. Make certain that the iPod is turned off and locked with the Agree switch toggled on before opening your iPod. This volition ensure that you lot don't accidentally plough it on while working on it.
3
Remove the back from the iPod. It is recommended that y'all utilise a especially-designed opening tool to pry the back off, only you can also utilize a thin flathead screwdriver. If you use a screwdriver, you run the risk of scratching the case.
- Some guides recommend a sturdy plastic guitar selection as a adept substitute tool.
- Insert the tool into the small scissure between the metal and plastic parts of the case.
- Work the opening tool effectually the edge, gently prying the back off the iPod.
- Press the tabs inside the vanquish using your tool to aid release the casing.
- When the case is open, don't force the two halves apart, as there is a pocket-sized ribbon cable attaching the front to the logic board.
4
Ensure that the hard bulldoze cables are secure. The large, rectangular metal object in your iPod is the hard bulldoze. Cheque the cables connecting the hard drive to the rest of the circuitry to brand certain that nothing has come loose.
- Gently lift the difficult bulldoze out of it's housing to reveal the connector cablevision underneath. Information technology is ordinarily connected to the logic board with black record. Remove the tape and printing the connector firmly into the board. Replace the tape and the gently supervene upon the hard bulldoze. This loose cable is the source of a significant number of hard drive problems.^[2]
5

Fold a business card in half. This volition create a square that will be thick enough to apply pressure onto the hard drive. If you don't accept a business carte handy, cutting a square out of a cardboard bar coaster volition work as well.
6

Place the concern card onto the difficult drive. Center the folded business card on the difficult drive, taking intendance not to disrupt whatsoever of the cables.
seven

Replace the backing on the iPod. With the card in place, push button the backing onto the iPod. Push it in with intendance, and ensure that all of the tabs click back into place.
8
Restore your iPod. After you replace the backing on the iPod, you will likely need to restore it in guild to ensure that nothing corrupt remains. Run across the showtime section of this article for detailed instructions.
- If you are still receiving difficult disk errors or hear a clicking audio, then your difficult drive nigh likely needs to exist replaced. See the next section for detailed instructions.
Advertisement

one
Ensure that there are no other options. This is 1 of the more than hard repairs to endeavour yourself, so brand sure that you can't fix the event using 1 of the other methods in this commodity first. If you've tried everything, yous can try replacing your hard drive as a last-ditch effort.
- If you iPod is making a clicking sound and the "distressing iPod" image appears on your screen, then the hard drive most probable needs to be replaced.
- Replacement hard drives can exist ordered online, or yous can scavenge a drive out of another iPod that is the same model.
- All versions of the iPod Touch, iPod Shuffle, and iPod Nano utilize wink memory instead of a traditional hard drive. This means there are no moving parts that can fail or connections that can become severed. At that place is no practical way to secure or supersede an iPod Bear upon hard drive, as the flash memory unit is built into the circuitry.
2

Toggle the Hold switch on. Make sure that the iPod is turned off and locked with the Concord switch toggled on before opening your iPod. This volition ensure that y'all don't accidentally turn it on while working on it.
3

Open up your iPod. Follow the steps in the previous method to remove the back from your iPod to expose the difficult bulldoze.
4

Lift up the hard drive. Lift the difficult drive from the top of the iPod. Don't endeavor to pull it out completely. Remove the prophylactic bumpers and shock absorber and set them to the side.
5

Pull the bulldoze out slightly. You will see a cable at the lesser the drive that attaches the drive to the circuitry. Gently work the cable out of the drive, using either your fingers or a screwdriver.
6

Remove the drive. In one case the cable has been detached, you lot should be able to completely remove the bulldoze from the housing. Once yous take pulled the drive out, take off the foam encompass and put information technology on your replacement drive. Put the rubber daze absorbers on it also.
7

Install the new drive. Insert the new bulldoze in the same direction that the sometime drive was installed. Gently insert the cablevision so that the hard drive can send and receive data from the iPod's motherboard. Close up the iPod and ensure that all of the tabs click.
8

Restore the iPod. With the new hard drive installed, all that is left is to perform a restore on the iPod. See the kickoff method in this commodity for detailed instructions on restoring the device.^[3]

Advertisement

1

Obtain a replacement screen. You lot volition demand to order a replacement screen for your iPod. Replacement screens can be ordered online for about $30 USD. Make sure to order the display for the fourth Generation iPod or Photo, or the brandish will not work.
2

Toggle the Hold switch on. Brand sure that the iPod is turned off and locked with the Hold switch toggled on before opening your iPod. This will ensure that you don't accidentally turn it on while working on it.
3
Open the iPod. A set of iPod opening tools is recommended for getting into the seam of the iPod to disengage the tabs. You lot can apply a thin apartment-head screwdriver if you don't have an iPod opening tool.
- Starting time by inserting your tool into the seam at the top of the iPod, near the headphone jack. Run the tool to the corner, creating an opening. Exit the tool inserted to keep the gap open up.
- Move the 2nd tool down the seam on both sides, releasing the tabs that concur the casing together. In that location are two tabs at the bottom virtually the dock connector.
4

Disconnect the two halves. Once you've separated the halves, gently open the iPod like a book. You volition notice a cable connecting the iPod's logic lath to a small board on the other one-half. This is the headphone connector, and needs to be removed to continue. Disconnect it from the iPod side past gently pulling the connector straight upwards.
v
Disconnect the difficult drive. Hold the hard drive with ane hand and pull the cable out from the bottom. You may demand to wiggle the cable slightly to get it loose. Remove the hard drive and fix it aside.
- Peel the tape off covering the hard drive cable's connectedness to the logic board. Flip up the black connector with your fingernail and pull the cable directly out. Set up the cable aside.
6

Disconnect the battery. On the bottom corner of the logic board yous will see a small, white connector. Gently pull this connector out, making sure that you are only grabbing the connector, and not the cables.
7

Disconnect the brandish and click wheel. On the reverse side of the battery connector, you lot will see a small connector with a black tab. Upwardly the side you lot will run across some other, larger connector with a blackness tab. Flip up both of these then that y'all can remove the ribbon cables from the connectors.
8

Remove the Torx screws. In that location are six Torx screws located effectually the edge of the logic board. You volition need to remove each of these to separate the logic board from the front panel. Advisedly remove the logic lath by gripping the edges of the large stop.
9

Remove the display. After you remove the logic lath, you will see the display panel. Pull this straight out to remove it. It may accept some adhesive, then you might have to wiggle it a flake. Replace information technology with your new screen, and and so follow these steps in reverse to shut upwardly the iPod.^[4]

Advertisement

1

Obtain a replacement screen. You volition need to order a replacement screen for your iPod. Replacement screens can be ordered online for near $20 USD. Make sure to order the display for the 5th Generation iPod with Video, or the brandish will not work.
2

Toggle the Concur switch on. Make certain that the iPod is turned off and locked with the Hold switch toggled on earlier opening your iPod. This will ensure that you don't accidentally turn it on while working on it.
3
Open your iPod. Use an iPod opening tool or a flathead screwdriver to gently by the front end casing from the back. Yous will need to disengage the tabs around the border of the iPod.
- Don't completely divide the two halves when you disengage all of the tabs. There are ribbons connecting the two halves that could get damaged if you pull information technology apart.
iv
Disconnect the bombardment cablevision. You will see a small, brownish latch holding a ribbon cablevision in place in one of the corners. Employ tweezers to lift the latch and so that you can slide the ribbon cablevision out.
- Don't pull the latch too hard, or you lot may accidentally split up the logic lath, which volition render your iPod substantially unusable.
5

Disconnect the headphone jack. At this point yous should have ane cable connecting the two halves of your iPod. This cable connects the headphone jack to your logic board. Elevator the hard drive up to reveal the dark-brown connector. Use your fingernail or opening tool to lift the latch on the connector and release the cable. Pull the cable out with your fingers and your iPod halves will now exist completely separated.
six

Remove the hard bulldoze. Lift the difficult bulldoze upward from the top of the iPod, and remove the ribbon cablevision that attaches it to the circuitry. You may need to use your opening tool to release the swivel on the motherboard connector cable. releasing information technology from the hard bulldoze.
7
Remove the front panel. On the each side of the iPod, yous should see several pocket-size screws. Remove these with a Phillips screwdriver and set the screws somewhere you won't lose them.
- Once the screws are removed, work the metal framework free. There will be a footling resistance, as the framework is usually lightly glued to go along information technology in place.
- The framework houses the logic board, front display, and click bike. Elevator it completely out of the forepart console.
8

Remove the brandish. On the logic lath, y'all will come across another ribbon cablevision connected. This cablevision attaches to the display. Flip the tab up that holds the ribbon in identify. Gently wiggle the brandish complimentary from the framework, and lightly pull it out. The ribbon cable will come with information technology.
9
Install your new screen. Now that the display is separated, you lot tin can install your new screen. Insert the new screen'south cable into the logic board and close the tab to secure it. Follow the previous steps in contrary to reattach all of your components and close up your iPod.
- You lot will probable need to perform a restore in one case your iPod has been put back together. Run across the showtime method in this article for details on how to restore your iPod.^[v]
Advertizing

i

Obtain a replacement screen. You will need to order a replacement screen and digitizer for your iPod. Replacement screens tin can be ordered online for about $25 USD. Make sure to order the brandish for the iPod Bear on Gen three, or the brandish will not work.
two
Open the iPod. Yous volition demand an iPod opening tool or a thin flat-caput screwdriver in order to separate the instance of your iPod touch. A screwdriver is more than likely to leave scratches than an iPod opening tool.
- Insert your tool into the seam between the glass and plastic near the volume buttons. Rotate the tool to pry the glass away from the casing. Proceed doing this around the edge of the iPod.
- Practice not run the tool downwards the seam. Instead insert, pry, and remove information technology to insert it in another location.
- Disassemble the clips around the within of the casing that hold the glass panel in place.
- Elevator the panel away from the residue of the iPod, lifting from the lesser. The panel will all the same be attached by a cable at the top.
3

Detach the cable attaching the panel to the iPod. This is located at the top of the iPod, and is very fragile. Y'all will demand to gently pry the connector off of the logic board with your opening tool.
four
Pry the brandish up. Insert the opening tool between the white backlight assembly and the metal panel beneath it. Insert the tool at the lesser end of the display, in the eye. Gently pry it up, taking intendance not to bend the screen every bit you do so. Rotate the display up, leaving the summit virtually the iPod.
- You volition need to proceed belongings this up while you work underneath information technology.
5
Remove the screws in the metal tray. underneath the display you lot volition run into a metallic tray with seven Phillips screws in it. You will need to remove all seven to go along.
- Lay the display back downward and remove another Phillips screw at the pinnacle border of the iPod.
6
Disconnect the brandish. Once all the screws have been removed, elevator the display upwards once more, and and then lift the newly-freed metal tray up. Rotate them both towards the superlative of the iPod.
- Peel the copper tape off of the meridian edge of the display. Exit it fastened to the metal tray.
- Skin the tape that covers the display cablevision. It is revealed when yous lift the metallic tray up.
- Pry the display cable out of its socket. This is located towards the lesser of the iPod underneath the metal tray. Peel the cablevision off the adhesive that keeps it fastened to the rear console.
7

Remove the display. With the cable disconnected, yous can lift the brandish out of the iPod. Lift the metallic tray a petty so that the display cable does not go caught when y'all lift the display unit out.
8

Install the new display. Take your new brandish and run the new brandish cable back to where you lot asunder it originally. Connect the cable then follow the in a higher place steps in opposite to secure everything and reassemble the iPod.^[6]

Advertisement

1

Obtain a replacement screen. You will need to order a replacement screen and digitizer for your iPod. Replacement screens tin be ordered online for about $100 USD. Brand certain to order the display for the iPod Touch Gen 5, or the display will non work.
2
Remove the front panel. To remove the front console of your iPod, y'all volition need a small, strong suction cup. Place the suction cup on front of the iPod, towards the bottom. The bottom edge of the suction cup should be covering the upper half of the Dwelling house push button. Printing the suction cup firmly to create a good seal.
- Hold the iPod firmly on a table or workbench with one paw, gripping the edges. With your other hand lift the suction cup. Pull firmly, as you lot will demand to pause the adhesive in order to lift it out.
- Only remove the front console nigh an inch or then.
iii
Release the frame. Once one cease of the panel has been lifted, you lot can start working on removing the small plastic frame that sits betwixt the front panel and the metallic bankroll. At that place are several clips running forth each side of the iPod. Insert your opening tool to release these clips, which will somewhen release the frame.
- One time the frame is released, flip the front panel upwards so that the insides are completely exposed. Accept intendance not to divide the halves at the elevation as they are still connected with cables. Lay both halves terminate to end on your work space.
four

Remove the screws securing the metal plate. The inside of the iPod is protected by a large metallic plate. You volition need to remove 11 screws in gild to have the metallic panel off. In one case the screws accept been removed, elevator the plate out of the iPod.
v
Remove the bombardment. In club to get at the cables in the iPod, you will need to remove the battery. First, remove the three screws at the top that secure the logic lath to the iPod instance.
- Insert the iPod opener tool into the notches around the battery. Gently pry the bombardment up using these notches.
- The battery is secured with a lot of adhesive, then you will need to proceed slowly and use all of the notches.
- Once the battery has been freed from the adhesive, flip information technology to the side of the example. Proceed slowly, every bit the cablevision is soldered to the logic board.
6

Pop the camera off. Use the opening tool to popular the front photographic camera out of it's housing at the top of the iPod. Information technology will flip out of the housing.
7
Remove the screws that secure the Lightning connector, headphone jack, and speaker. These can be found at the bottom of the iPod. You will demand to remove an edge of the copper tape to reveal one of the screws. There are five screws total: three around the Lightning connector, and two holding the headphone jack and speaker.
- Pry the speaker out of the instance once you take removed the screws.
- Pull the Lightning connector out by gripping the big apartment cable and pulling gently.
viii
Disconnect the brandish. Flip everything over, and you lot will run into the back of the logic board. On the border of the board, you volition run across a cable connecting the logic board to the digitizer. Use your opening tool to remove the cable.
- Disconnect the display cable (divide from the digitizer cable) from its socket on the logic board.
- Flip the Lightning connector assembly up and peel the display cable off of the logic board.
9

Install the new brandish. Pull the erstwhile brandish associates out of the iPod one time it'south all separated. Install the New display assembly and follow these steps in reverse to secure all of the components and close upward the iPod.^[7]

Advertisement

Add New Question

Question

What tin can I do if I oasis't charged my iPod for a month, and the home push doesn't work?

Plug the iPod into the charger and give information technology 30 to hr. If the home button still isn't working, you should have it to the Apple store for assistance. It may just demand to charge for a chip before information technology will plow back on.
Question

Where can I go a protector for my iPod Bear on half-dozen?

At any store that sells electronics, similar Best Purchase. It will exist where the telephone accessories are.
Question

What should I practise if my iPod is interim really weird?

You lot have to describe what it is doing specifically for anyone to be able to help you. "Acting really weird" is too vague and could mean a lot of things.
Question

How tin can I gear up my 6th generation iPod?

The aforementioned way y'all'd fix a 5th generation. Information technology depends on what exactly is wrong with it.
Question

How do I set an iPod touch that won't turn on?

Agree both the power button and dwelling house push button down until the Apple logo appears. This strength reboots your device and forces it to turn on.
Question

How tin I fix an iPod that just shows the Apple log and then turns off again?

Press the power button for 3 seconds. Keep holding the power push button and press the home push together, for 15 seconds. Then leave ability button, but keep holding downward the power push, for xx seconds. iTunes volition practice the residual, and you but demand to follow the instructions!
Question

What practise I do if the slider won't work on my iPod?

Agree the power button for 25 seconds and then agree the camera for 15 minutes. And so information technology volition become you dorsum on it again.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Before trying these methods, contact Apple and run into if you can become your iPod replaced for free.

Thank you for submitting a tip for review!

Opening the iPod will void whatsoever remaining warranty. Only perform internal repairs on devices that are no longer covered.

About This Article

Article Summary X

When your iPod is frozen or unresponsive, outset attempt toggling the Concur switch on and off a few times to see if that activates it. You tin also endeavour charging it for an hour to see if the battery is dead. If the iPod is on but won't answer to whatever input, printing and agree the ability button for 8-x seconds to perform a reset. Finally, if all else fails, try connecting your iPod to your computer and doing a factory restore. Back up your iPod first if you tin can so that you don't lose your information and settings. Keep reading for more than advice, including how to rescue an iPod that's gotten wet!

Did this summary aid you?

Thanks to all authors for creating a folio that has been read 641,504 times.